Bathtub installation in Mount Pleasant, TX, fitted and sealed

Bathtub installation is the professional fitting of a new bathtub in a Mount Pleasant, TX home, with the drain, overflow, and seal checked before handover. A new tub should sit level, drain cleanly, and never leak at the overflow. NTP Plumbing installs bathtubs across Mount Pleasant, TX — drain and overflow set, trap checked, tested full before we leave. Open 24 hours, Monday through Sunday.

New bathtub being installed in a Mount Pleasant, TX bathroomNew tubDrain setTested full
  • Floor protectedDrop cloths down before tear-out
  • Drain testedTwo fills before surround goes back
  • Level checkedRim checked across the tub
  • Debris hauledOld tub leaves with us

What is included in a bathtub installation

Every install includes the tear-out, the plumbing connections, and the cleanup. What changes from job to job is the drain condition, the valve age, and whether the surround has to be rebuilt. We price those before we start so there is no surprise on the invoice.

New bathtub being installed in a Mount Pleasant, TX bathroom
  • Old tub removal and haul-away

    We cut the old tub free, protect the floor and doorways, and haul the unit off. You are not left with a tub in the yard or a dumpster rental to arrange.

  • Drain and overflow assembly

    We replace the drain shoe, overflow gasket, and drain assembly on every install. Reusing old parts is how leaks start, so we do not do it.

  • Supply line and valve check

    We inspect the shutoff valves and supply lines while the wall is open. If the valves are old or the lines are corroded, we swap them before the new tub goes in.

  • Level set and seal

    The tub goes in on a level bed, the rim is checked for level, and the surround joints are sealed with the right caulk for the material. We fill and drain the tub twice to test the joints.

  • Permit and inspection

    When the job requires a permit in Mount Pleasant, we pull it and handle the inspection. The work is on record for resale and the install meets 2024 International Plumbing Code adopted by the City of Mount Pleasant (Ordinance 2026-2, effective 20 January 2026).

  • Cleanup and walk-through

    We clean the work area, haul off the debris, and walk you through what was done and how to care for the new finish. You get a clear picture before we leave.

Homes and rentals

A replacement and a new-build install are different jobs — one starts with an old tub and a drain of unknown condition, the other with a fresh rough-in — but the checks at the end are the same in a home and a rental. What changes is the access, the schedule, and who needs the paperwork for a bathtub installation job.

For homes and rentals

We install tubs in houses, duplexes, and rental units across Mount Pleasant. Tenants and homeowners get the same walk-through and the same cleanup before we leave.

  • Cracked or rusted tub
  • Walk-in tub for a parent
  • Remodel rough-in before tile

For rentals and property managers

We handle tub swaps for rental turnovers and small multifamily properties. Scheduling works around the turnover, and the work is documented for the file.

  • Turnover tub replacement
  • Multifamily unit swap
  • Permit and inspection handled

What bathtub installation in Mount Pleasant, TX actually involves

A plain-language look at what Bathtub Installation involves and when it is needed. The City of Mount Pleasant charges a $75 residential plumbing permit fee where a permit is required (inside city limits) — that is a City fee, not our price.

See how it works

Installing a tub starts with the floor and the drain. The old tub comes out, the subfloor is checked for softness, the drain and overflow are set at the right height, and the new tub is levelled and bedded so it does not flex. Then it is filled and drained while we watch the overflow, the trap and the drain connections for a weep.

Most installs in Mount Pleasant, TX are replacements in older bathrooms — Downtown homes and Southgate ranches where the original tub is stained, cracked or sitting on a soft floor — and finish work in Northwood, Stone Briar and Deer Park Estates new builds. A tub that flexes will crack its seal within a year, so the bedding matters as much as the drain. Bathtub installation work follows the 2024 International Plumbing Code adopted by the city.

A tub install is a floor job with a tub on top of it.

New bathtub being installed in a Mount Pleasant, TX bathroom
What it is
Removing an old tub and fitting a new one on a sound floor, with the drain and overflow set.
When you need it
A cracked tub, a soft floor underneath, or a remodel that calls for a new fixture.
What to expect
A level tub, a clean drain, and a floor that stays dry when the tub is full.

How our install day runs

Every install follows the same sequence so there are no surprises mid-job. Here is what you can expect from the moment we arrive to the final walk-through.

  1. Walk-through and shutoff

    We look at the existing tub, the surround, and the access panel, then shut off the water at the main or the fixture valves. You get a clear rundown of what we found and what it changes about the job before any tools come out.

    • Walk-through
    • Shutoff
    • Quote confirmed
    New bathtub being installed in a Mount Pleasant, TX bathroom
  2. Tear-out and inspection

    We cut the old tub free, protect the floor and doorways, and haul the unit out. With the wall open we inspect the drain rough-in, the subfloor, and the framing for soft spots or old water damage. If something needs attention, we show you before we proceed.

    • Tear-out
    • Floor protected
    • Inspection
    New bathtub being installed in a Mount Pleasant, TX bathroom
  3. Rough-in corrections

    This is where the drain and supply lines get squared away. We replace the overflow and drain assembly, swap old shutoff valves for quarter-turn valves, and install new supply lines. If the drain line is cast iron and scaled shut, we run a drain snake or camera to confirm it is clear.

    • Drain check
    • Valve swap
    • Supply lines
    New bathtub being installed in a Mount Pleasant, TX bathroom
  4. Set and connect the tub

    The new tub goes in on a level bed, the drain and overflow connect, and the supply lines tie into the valve. We check level across the rim and confirm the apron sits flush. Then we fill and drain the tub twice to test the joints before the surround goes back.

    • Level set
    • Drain connect
    • Two-fill test
    New bathtub being installed in a Mount Pleasant, TX bathroom
  5. Seal, clean, and walk-through

    We seal the surround joints with the right caulk for the material, clean up the work area, and walk you through what was done. You get the old tub hauled off and a clear picture of how to care for the new finish.

    • Seal
    • Cleanup
    • Walk-through
    New bathtub being installed in a Mount Pleasant, TX bathroom

Tools and methods we use

Move across a circle, or focus it and press Enter, for an illustrative thermal view of this bathtub installation photograph.

  • New bathtub being installed in a Mount Pleasant, TX bathroom

    Pipe wrench and drain snake

    Used to break loose old drain connections and clear a scaled or clogged drain line before the new tub is set.

  • Plumber replacing old pipe with new PEX in a Mount Pleasant, TX home

    PEX crimping tool and Push-to-connect fittings

    Used to make clean, code-compliant supply line connections when we replace old valves or corroded lines behind the tub wall.

  • Plumber using leak detection equipment in a Mount Pleasant, TX home

    Leak detection microphone

    Used to find hidden leaks in the drain or supply lines before we close the wall, so we are not guessing.

  • Plumber running a sewer camera inspection in Mount Pleasant, TX

    Sewer camera

    Used to inspect the drain line under the tub when the line is old cast iron or the tub has been backing up.

  • Plumber soldering a copper pipe joint under a kitchen sink in a Mount Pleasant, TX home

    Soldering torch and copper pipe

    Used when the existing plumbing is copper and the valve or drain connection has to be sweat-soldered to code.

Thermal views are illustrative, generated from photographs of bathtub installation work in Mount Pleasant, TX.

Methods

  • Pressure gauge

    Used to check supply pressure before the new valve goes in, so the fixture is not stressed by high pressure.

  • 2024 International Plumbing Code rough-in

    We set the drain, overflow, and valve to IPC dimensions so the tub and surround fit correctly.

  • Mortar bed setting

    The tub base is set in mortar or a manufacturer-approved bed so it does not flex or rock. A level, solid base is what keeps the drain joint from failing.

  • Two-fill drain test

    We fill and drain the tub twice before the surround goes back up. If a joint is going to leak, it shows up in the test, not in your ceiling a month later.

  • Permit and inspection

    When the job requires a permit in Mount Pleasant, we pull it and meet the inspector. The work is on record and meets code.

When a bathtub installation makes sense

New bathtub being installed in a Mount Pleasant, TX bathroom

Bathroom remodel

A remodel needs a new tub where the old one was.

We checked the subfloor, set the drain and overflow, levelled and bedded the new tub, and tested it full.

Outcome: A level tub with a dry floor and a clean drain.

New bathtub being installed in a Mount Pleasant, TX bathroom

Cracked tub

The old tub is cracked through and leaks into the room below.

We removed the tub, checked the floor underneath, and set the new one on a sound, level base.

Outcome: A dry room below and a tub that holds water.

New bathtub being installed in a Mount Pleasant, TX bathroom

Soft floor

The tub flexes when you step in and the seal keeps cracking.

The subfloor was soft. We repaired the floor first, then set the tub on a solid base.

Outcome: A tub that does not move, with a seal that stays put.

New bathtub being installed in a Mount Pleasant, TX bathroom

New build finish

A new-build bathroom needs its tub set.

We fitted the tub on the new rough-in, set the drain and overflow, and tested it full before the tile went in.

Outcome: A finished bathroom, tested and dry.

New bathtub being installed in a Mount Pleasant, TX bathroom

Rental turnover

A rental bathroom needs a new tub before the next tenant.

We coordinated with the property manager, removed the stained old tub, and installed the new one with the drain checked.

Outcome: A fresh bathroom ready for move-in day.

New bathtub being installed in a Mount Pleasant, TX bathroom
DowntownSouthgateNorthwood

How bathtub installation runs in Mount Pleasant, TX

Replacement installs cluster in the older stock: Downtown bathrooms from the 1940s–1980s and Southgate's 1970s ranches, where the original tubs are reaching the end of their life and the floors underneath need checking. New-build bathtub installation installs happen in Northwood, Stone Briar and Deer Park Estates, where the rough-in is new and the job is straightforward.

Greenhill Park and Country Club Estates custom homes often want larger tubs, which means the drain sizing and the floor support matter more. For a wider look at where new bathtub plumbing goes in around town, see our post on the best neighborhoods in Mount Pleasant, TX for new plumbing installations.

  • Downtown Mount Pleasant, TX: Remodels in early-to-mid-20th-century bathrooms. The floor under the old tub often needs attention before the new one goes in.
  • Southgate: 1970s brick ranches where bathroom refreshes are common. A new tub usually goes in with the drain and overflow replaced.
  • Northwood and Stone Briar: Newer north-side subdivisions, where bathtub installation installs are usually finish work on a new build or a bathroom refresh.
  • Greenhill Park: Custom homes inside the Country Club community with larger tubs. Drain sizing and floor support matter more here.
  • Lake Bob Sandlin area: Lakefront homes where bathtub installation installs happen between stays. We test the tub full before we leave.
  • Floor first: A tub that flexes cracks its seal within a year. We check the subfloor before setting the tub, not after.
See where we work
  • Walk-through and price before tools come out
  • Floors and doorways protected during tear-out
  • Two-fill drain test and cleanup before we leave

From problem to finished result

Example — a typical call. The stories below are illustrative examples of the kind of bathtub installation calls we take, not a record of a specific past job.

New bathtub being installed in a Mount Pleasant, TX bathroom
IllustrativeThe thermal view for this bathtub installation job is generated from the photograph. It is not a measurement. Drag the handle to compare the before and after on this bathtub installation job, or use the arrow keys once it is focused.
  • Rusted cast iron tub replaced in Northwood

    Before: The tub had rusted through the floor and was leaking into the ceiling below. The drain line was original cast iron and scaled shut, and the shutoff valves would not close.

    After: We pulled the tub, snaked the drain line, replaced the shutoff valves with quarter-turn valves, and set a new alcove tub on a level bed. The two-fill test held.

    Run the tub fan after showers and check the caulk line at the surround joint twice a year. A softener keeps scale off the new finish.

  • Walk-in conversion in Southgate

    Before: An older homeowner could not step over the high tub apron safely. The existing drain was undersized for the faster fill and dump rate of a walk-in tub.

    After: We corrected the drain, set the walk-in tub on a level bed, installed grab bars, and tested the door seal twice before we left. The tub fills and drains without leaking.

    Wipe the door seal dry after each use and check the drain screen weekly. A softener keeps the seal and finish clean.

  • Remodel rough-in in Downtown Mount Pleasant, TX

    Before: A bathroom remodel was stalled because the new tub did not match the existing rough-in. The old valve was set too shallow for the new surround.

    After: We reset the valve to the correct rough-in depth, connected the drain, and set the tub level so the tile crew had a square surface.

    Check the caulk line at the surround joint once a year and reseal if it pulls away. Keep the drain screen in place to catch hair.

Problems a new tub solves

Most tub replacements start with a problem that a repair will not fix. Here are the ones we see most often in Mount Pleasant homes.

  • Cracked tub leakCracked or rusted-through tub leaking belowWater reaches the subfloor and ceiling below, and the damage spreads every time the tub is used. A patch will not hold on a rusted-through floor. We pull the failed tub, inspect the subfloor for rot, and set a new tub on a solid base. The drain and overflow are replaced so the leak path is closed, not patched.
  • Tub rocks or flexesTub that rocks or flexes when you step inA rocking tub stresses the drain joint with every step, and the joint fails over time. It also cracks the caulk line and lets water behind the surround. We set the new tub on a mortar or manufacturer-approved bed, check level across the rim, and confirm the apron sits flush before the surround goes back up.
  • Slow tub drainSlow or backed-up tub drainStanding water in the tub is a sign the drain line is clogged or scaled. Installing a new tub over a bad drain means the problem comes right back. We run a drain snake or camera before the install. If the line is cast iron and scaled shut, we correct it first so the new tub drains properly from day one.
  • Valves will not closeOld shutoff valves that will not closeA valve that will not shut off means the whole house has to be shut down for the next repair. It also makes a simple fix into a bigger job. We swap old valves for quarter-turn shutoffs while the wall is open during the install. The next repair is a simple shutoff instead of a house-wide shutdown.
  • High tub apronTub that is hard to step overA high tub apron is a fall risk for older homeowners and anyone with mobility issues. It is the most common reason people ask about a walk-in conversion. We install a walk-in tub with a low threshold, grab bars, and a door seal tested before we leave. The drain is checked to handle the faster fill and dump rate.

Why a proper install pays you back

A level tub, a new drain, and a seal that holds.

  • No leaks under the floor

    The overflow gasket and drain shoe are the two spots that fail first. We replace the wax ring and drain assembly on every install and pressure-test the drain before the surround goes back up, so water goes down the line instead of into your subfloor.

  • Level base, no flex

    A tub that rocks puts stress on the drain joint every time someone steps in. We set the base in mortar or a manufacturer-approved bed, check level across the rim, and confirm the apron sits flush before we close anything up.

  • Correct valve and supply lines

    Old shutoff valves behind a tub are a common failure point. We swap them for quarter-turn valves and new supply lines while the wall is open, so the next repair does not mean tearing out tile. That is the difference between a cheap install and a smart one.

  • One crew, start to finish

    We pull the old tub, set the new one, connect the drain and supply, and seal the surround, and we haul the old tub off with us so you are not stuck with it in the yard.

What you receive with bathtub installation

Clear records from your bathtub installation job that you can keep and share.

Job photos

Drain and valve shown before closing wall

Permit record

Inspection on file when required

Care sheet

How to maintain the new finish

Haul-away slip

Old tub removed from the property

Alcove, walk-in, and freestanding tubs differ

The tub type changes the drain, the valve depth, and the surround work, so it changes the job.

Alcove tub

Fits between three walls in a standard opening

  • Standard drain rough-in
  • 60-inch standard opening
  • Surround stays or rebuilds

Walk-in tub

Low threshold with a door and grab bars

  • Drain sized for fast dump
  • Door seal tested twice
  • Grab bars fitted

Freestanding tub

Stands alone with a floor-mounted or wall valve

  • Floor drain relocation
  • Valve depth checked
  • Access for the fill line

Materials and systems we work with

  • Copper pipe
  • PEX tubing
  • PVC pipe
  • Cast iron pipe
  • Wax ring
  • Supply lines
  • Shutoff valves
  • Pipe fittings

Service ZIP codes

A list like this tells people straight away whether we cover their street for bathtub installation. Not listed? Call and ask — it only takes a minute.

  • 75455
  • 75456

Areas we serve in Mount Pleasant, TX

Based in Mount Pleasant and covering the places around it. Pick one for local details.

View all service areas

What customers say about our tub installs

Excellence service and diagnosis with courtesy and understanding of the whole issue. Went well beyond the norm to assist whereby I was able to resolve the problem. Especially considering it was a Saturday morning service call Thank you so much for your expert advice. Hot water again, yeah!!!

SamE Embras Jr
5 stars · 2 years ago · Google review

The service I received from NTP Plumbing in April was Absolutely EXCEPTIONAL! The technician/plumber name was Jeremy. He took care of my pipe issues efficiently and treated me like I was family. Jeremy had excellent customer service/interpersonal skills and he made sure the work done was in the spirit of excellence. I would be remiss if I didn't mention the wonderful service I received from the owner, James. He was so welcoming and genuinely kind. James was able to get me scheduled in so that my plumbing would be taken care of in a timely manner. Thank you NTP Plumbing for all you do and especially for the things I don't see.

Ozie Hollingsworth
5 stars · 2 years ago · Google review

I recently used NTP for a clogged kitchen drain. The job took longer than anticipated but James honored his quote and the work is guaranteed for 30 days. I would highly recommend NTP for any plumbing needs you may have.

No Name
5 stars · 2 years ago · Google review

This review is about a used-appliance sale, a separate line of business — not plumbing work.

They sell used appliances as well, fyi they r super nice ND very great prices! They delivered my fridge same day we're quick and nice. Thank y'all so much for being so efficient!!

Brittney Moss
5 stars · 2 years ago · Google review

They were very professional and courtious. Fixed all my plumbing problems

Tim Griffin
5 stars · 4 years ago · Google review

4.8 out of 5 from 16 Google reviews — 15 five-star and 1 one-star. Read all reviews for NTP Plumbing on Google.

All reviews
4.8 out of 5 · 16 Google reviews

Frequently Asked Questions

Most installs are finished while we are there when the rough-in is already there. If the floor under the old tub is soft, the repair adds time — we will tell you what we find before we start.

Yes. We install the tub you supply, and we will tell you before we start if the drain position or the floor needs anything different.

Only if the tub was the problem. A slow bathtub drain is usually the trap or the drain line. We check the drain before recommending a new tub.

Yes. We fill the tub to the overflow and drain it while we watch the overflow, the trap and the connections. If anything weeps during a bathtub installation job, it gets fixed on the spot.

Get bathtub installation in Mount Pleasant, TX scheduled

Call (903) 350-9085 and tell us what tub you want fitted. We will check the floor and the drain, and test it full before we leave. Open 24 hours, Monday–Sunday.

Get in Touch with NTP Plumbing

Call (903) 350-9085 any time — NTP Plumbing is open 24 hours, Monday–Sunday. Tell us what you are seeing and we will talk you through shutting the water off if you need to. We serve Mount Pleasant, TX, including ZIP codes 75455 and 75456.

Thanks. Your request is in and the team will follow up shortly.