Shower repair in Mount Pleasant, TX that restores the pressure

Shower repair is the professional fixing of a leaking, slow-draining, or poorly running shower in a Mount Pleasant, TX home. A shower that drips all day or runs at a trickle is usually one worn part away from working properly. NTP Plumbing repairs showers across Mount Pleasant, TX — valves, cartridges, diverters and leaks — and checks the supply lines while we are in the wall. Open 24 hours, Monday through Sunday.

New shower being installed in a Mount Pleasant, TX bathroomValve fixedPressure backLeak stopped
  • Water shut firstWe isolate the line before opening anything
  • Parts matchedCartridge and seats replaced as a set
  • Pan protectedTile and pan covered during the repair
  • Tested before leavingHot and cold run, drip check done

What is included in a shower repair visit

Every shower repair starts with a full inspection of the fixture, not just the part you noticed. We check the valve, the showerhead and arm, the drain, and the pan, then tell you what needs fixing and what can wait. The list below covers what a standard repair includes. If we find something outside that scope, you hear about it before we do the work.

New shower being installed in a Mount Pleasant, TX bathroom
  • Valve and cartridge inspection

    We pull the handle and trim, inspect the cartridge, seats, and valve body, and confirm whether the leak is at the cartridge or deeper in the valve.

  • Showerhead and arm check

    We check the showerhead, supply arm, and connection for clogs, cracks, and thread damage, and replace worn parts so flow and spray pattern are correct.

  • Drain and pan inspection

    We test the drain for slow flow and check the pan and flange for movement or cracks that let water into the subfloor.

  • Pressure and temperature test

    After the repair, we run hot and cold water and confirm the valve holds temperature and pressure without dripping or scalding.

  • Cleanup and haul-off

    We protect the pan and tile, contain dust, and remove old parts and packaging so the bathroom is ready to use when we leave.

Homes and rentals

A dripping valve and a leaking pan are different repairs — one is a cartridge inside the wall, the other is the drain and the pan below — but the checks at the end are the same in a home and a rental. What changes is the access, the schedule, and who needs the paperwork for a shower repair job.

For homes and renters

Shower problems show up at the worst times, usually before guests or a work week. We inspect the valve, drain, and pan, then tell you what needs fixing now and what can wait.

  • Handle drips or sprays
  • Ceiling stain below shower
  • Low pressure or temperature swings

For rentals and property managers

A failed shower valve in a rental turns into a tenant call fast. We diagnose, repair, and document the work so the property file stays current.

  • Multi-unit valve failures
  • Tenant shower complaints
  • Drain backups in rentals

What shower repair in Mount Pleasant, TX actually involves

A plain-language look at what Shower Repair involves and when it is needed. The City of Mount Pleasant charges a $75 residential plumbing permit fee where a permit is required (inside city limits) — that is a City fee, not our price.

See how it works

Most shower repairs come down to the valve: a cartridge that no longer mixes properly, so the temperature swings hot and cold, or a diverter that will not send the water where you want it. A shower that drips from the head when it is off is usually the same cartridge failing to seal. We identify the valve, fit the matching cartridge, and test the temperature and the shutoff before we leave.

Low pressure at the shower is a different problem, and in Mount Pleasant, TX it often traces back to the house, not the showerhead: galvanised supply lines from the 1940s–1960s era narrow with corrosion, and a scaled head only makes it worse. We check the pressure at the shower and at the meter, so we fix the cause rather than the symptom. Shower repair work follows the 2024 International Plumbing Code adopted by the city.

A shower that will not hold its temperature is a valve asking for a new cartridge.

New shower being installed in a Mount Pleasant, TX bathroom
What it is
Replacing the worn cartridge, diverter or seal inside a shower valve so it mixes and shuts off cleanly.
When you need it
A dripping head, temperature swings, a stuck diverter, or pressure that has faded.
What to expect
The failed part replaced, the temperature tested, and the wall checked for leaks.

How our shower repair process works

You call, we show up, and we tell you what is wrong before we touch anything. Here is the sequence from first call to final test, so you know exactly what to expect.

  1. Call and schedule

    You describe the symptom, a drip, a spray, a slow drain, or no hot water at the shower. We ask a few questions to narrow it down and schedule a visit, often quickly for active leaks. We confirm the address and agree a visit time with you.

    • Call
    • Describe
    • Schedule
    New shower being installed in a Mount Pleasant, TX bathroom
  2. Diagnose on site

    We shut off the water, pull the handle and trim, and inspect the cartridge, seats, and valve body. We check the showerhead and arm, the drain, and the pan for movement or soft spots. If water is showing up in a ceiling below, we use a leak detection microphone and moisture meter to confirm the path.

    • Shut off
    • Inspect
    • Confirm
    New shower being installed in a Mount Pleasant, TX bathroom
  3. Explain and price

    We tell you what failed, what we recommend, and what it costs before any work starts. If the valve body is cracked and needs replacement rather than a cartridge, you hear that up front. No surprise line items after the wall is open.

    • Explain
    • Price
    • Approve
    New shower being installed in a Mount Pleasant, TX bathroom
  4. Make the repair

    We replace the cartridge, seats, showerhead, drain assembly, or supply lines as needed, using parts that match your fixture. We protect the pan and tile, keep the work area contained, and solder or crimp PEX and copper connections to code.

    • Replace
    • Seal
    • Connect
    New shower being installed in a Mount Pleasant, TX bathroom
  5. Test and clean up

    We restore the water, run the shower hot and cold, and check for drips at the handle, arm, and drain. We confirm the pan holds and the flow is right. Then we clean up, haul off old parts, and walk you through what we did and how to keep it working.

    • Test
    • Clean
    • Walkthrough
    New shower being installed in a Mount Pleasant, TX bathroom

Tools and methods we use on shower repair

Move across a circle, or focus it and press Enter, for an illustrative thermal view of this shower repair photograph.

  • Plumber repairing a shower valve in a Mount Pleasant, TX bathroom

    Leak detection microphone

    Used to hear water escaping behind tile or under a pan when the source is not visible, so we open only the area that needs it.

  • Plumber using leak detection equipment in a Mount Pleasant, TX home

    Moisture meter

    Confirms how far water has spread in drywall, framing, and subfloor so we know whether a repair or a larger dry-out is needed.

  • Plumber soldering a copper pipe joint under a kitchen sink in a Mount Pleasant, TX home

    Pipe wrench and adjustable wrench

    Used on shower arms, supply lines, and valve nuts where a proper bite matters and rounded fittings cause bigger problems.

  • Plumber replacing old pipe with new PEX in a Mount Pleasant, TX home

    PEX crimping tool

    Makes code-correct connections when we replace a section of supply line with PEX tubing during a valve or pipe repair.

  • NTP Plumbing technician with tools at a Mount Pleasant, TX home

    Soldering torch

    Used for copper pipe connections when the existing plumbing is copper and a soldered joint is the right repair.

Thermal views are illustrative, generated from photographs of shower repair work in Mount Pleasant, TX.

Methods

  • Drain snake

    Clears hair and soap scum from the shower trap when the drain is slow but the pan and flange are still sound.

  • Pressure gauge

    Checks supply pressure at the valve so we can tell whether low flow is a fixture problem or a line problem.

  • Isolate before opening

    We shut off the water and confirm which fixture is leaking before we open a wall. That keeps the repair focused and avoids unnecessary demolition.

  • Replace cartridge and seats together

    A new cartridge in worn seats will drip again. We replace both as a set, which is why the repair holds up.

  • Pressure test after repair

    Every repair is tested with water on and the shower running hot and cold. We check the handle, arm, and drain before we call the job done.

  • Code-correct connections

    We work to the 2024 International Plumbing Code adopted by the City of Mount Pleasant (Ordinance 2026-2, effective 20 January 2026) and International Plumbing Code, using soldered copper or crimped PEX and new shutoff valves where the old ones are worn.

When Mount Pleasant homeowners call for shower repair

New shower being installed in a Mount Pleasant, TX bathroom

Dripping head

The shower head drips all day even with the handle off.

The cartridge had worn through. We fitted the matching cartridge and the drip stopped.

Outcome: A silent shower and a water bill that stops climbing.

New shower being installed in a Mount Pleasant, TX bathroom

Temperature swings

The shower runs hot, then cold, every time another tap runs.

The mixing cartridge could no longer hold the balance. A new cartridge restored steady temperature.

Outcome: A shower that stays where you set it.

New shower being installed in a Mount Pleasant, TX bathroom

Low pressure

The shower runs at a trickle while the kitchen tap is fine.

The head was scaled and the supply run was narrowing. We cleaned the head and found the galvanised run behind it, and laid out the replacement.

Outcome: Full pressure at the head, with the cause explained.

New shower being installed in a Mount Pleasant, TX bathroom

Leak behind the wall

A stain on the ceiling below the bathroom keeps growing.

We found the valve leaking inside the wall, opened one small section, and repaired the connection.

Outcome: A dry ceiling and a valve that holds.

New shower being installed in a Mount Pleasant, TX bathroom

Stuck diverter

The diverter will not send water to the showerhead.

The diverter cartridge was seized with scale. We replaced it and the shower works from the handle again.

Outcome: A diverter that moves and a shower that runs.

New shower being installed in a Mount Pleasant, TX bathroom
DowntownSouthgateNorthwood

How shower repair runs in Mount Pleasant, TX

Shower calls split by house age. In Downtown homes and Southgate ranches, the valves are often original and the cartridges are worn through; in newer Northwood and Stone Briar homes, the fault is usually a single cartridge or a scaled head. Low pressure at the shower is the tell for galvanised supply lines narrowing with corrosion.

Leaks behind the shower wall are the quiet ones — they show as a stain on the ceiling below or a soft spot in the drywall, and they need finding before they rot the framing. For the water-bill side of a dripping shower, our post on how to lower your water bill with simple plumbing fixes covers what a drip costs and what to check first.

  • Downtown Mount Pleasant, TX: Early-to-mid-20th-century bathrooms where shower valves are often original. Worn cartridges and temperature swings are the usual repair.
  • Southgate: 1970s brick ranches with aging shower valves. Dripping heads and stuck diverters are common here.
  • Northwood and Stone Briar: Newer north-side subdivisions, where shower repair work is usually on newer systems. The fault is usually one cartridge or a scaled head, fixed while we are there.
  • Country Club Estates: Golf-course custom homes on Greenhill Road with larger showers and multiple heads. Valve and diverter work is common here.
  • Low pressure at the shower: Often a galvanised supply line narrowing with corrosion, not a bad showerhead. We check the pressure at the shower and at the meter.
  • Leaks behind the wall: A stain on the ceiling below or soft drywall means a valve leak inside the wall. We find it before it rots the framing.
See where we work
  • We walk the bathroom and inspect the full fixture
  • We protect the pan and tile before starting
  • We test the repair and explain what we did

From problem to finished result

Example — a typical call. The stories below are illustrative examples of the kind of shower repair calls we take, not a record of a specific past job.

New shower being installed in a Mount Pleasant, TX bathroom
IllustrativeThe thermal view for this shower repair job is generated from the photograph. It is not a measurement. Drag the handle to compare the before and after on this shower repair job, or use the arrow keys once it is focused.
  • Dripping shower valve in Downtown Mount Pleasant, TX

    Before: A homeowner had a shower that dripped steadily from the handle for months. The trim was stained and the water bill had climbed. The cartridge was worn and the seats were pitted from hard water scale.

    After: We replaced the fixture cartridge and seats as a set, cleaned the valve body, and tested hot and cold. The drip stopped completely, and the flow was stronger than it had been in years.

    Run the shower hot for a minute each week to keep the cartridge moving, and consider a water softener to slow scale buildup.

  • Ceiling stain from a cracked drain flange

    Before: Water was showing on the ceiling below an upstairs shower in Southgate. The drain flange was cracked and letting water past the pan.

    After: We traced the leak with a moisture meter, replaced the drain flange, and confirmed the pan held water. The ceiling dried out and the stain stopped spreading, avoiding a full bathroom remodel.

    Check the drain for movement once a year and keep a strainer in place to stop hair from stressing the flange.

  • Low pressure fixed with a new showerhead and valve

    Before: A Northwood homeowner had weak flow and temperature swings whenever the toilet flushed. The showerhead was scaled shut and the pressure-balance cartridge was failing.

    After: We replaced the showerhead and the pressure-balance cartridge, flushed the supply line, and tested the valve. Flow came back to normal and the temperature stayed steady through a full flush test.

    Soak the showerhead in vinegar every few months to dissolve scale, and replace the cartridge at the first sign of a drip.

Shower problems we solve in Mount Pleasant

Most shower calls fall into a few categories. Here is what we see most often and what happens if you leave it alone.

  • Handle dripShower drips constantly from the handleA steady drip wastes water, stains the trim, and can seep behind tile into the wall cavity over months. We replace the cartridge and seats together, not just the cartridge, and test the valve under pressure. Most handle drips are fixed with parts we stock on the truck.
  • Ceiling stainWater stains on the ceiling below the showerThis usually means a failed drain flange, pan liner, or valve connection, and the damage spreads every time the shower runs. We use a leak detection microphone and moisture meter to trace the source, then repair the drain, pan, or valve connection. We confirm the pan holds before we leave.
  • Low pressureLow water pressure or inconsistent temperatureMineral buildup and a failing pressure-balance cartridge cause temperature swings that can scald when someone flushes a toilet. We clean or replace the showerhead, flush the supply line, and test the valve. If the cartridge is failing, we replace it with a matching part.
  • Slow drainSlow shower drain that backs upHair and soap scum clog the trap, and standing water stresses the pan and drain flange until it cracks. We clear the trap with a drain snake or hydro jetter and inspect the drain assembly for cracks. If the flange is failing, we replace it before it leaks into the subfloor.

What a proper shower repair gets you

A correct repair stops the leak, restores pressure, and protects the framing behind the tile.

  • Stop the water waste

    A showerhead that drips a steady stream can waste a lot of water over a month and show up on your next bill. We replace worn cartridges, seats, and showerheads so the flow shuts off clean. Every repair includes a flow check before we pack up.

  • Protect the framing

    Water that escapes behind tile or under a pan liner does not dry out. It feeds mold and rots studs and subfloor. We trace the source with a leak detection microphone and moisture readings, then repair the failed connection or seal before the damage spreads into the room below.

  • Restore real pressure

    Low flow is usually a clogged showerhead, a failing pressure-balance cartridge, or mineral buildup in the supply line. We flush the line, clean or replace the head, and test the valve so you get consistent temperature and pressure back, not a trickle that changes when someone flushes a toilet.

  • Fix it once, not twice

    Cheap fixes that skip the cause come back. We replace the whole cartridge and seats together, use new supply lines and shutoff valves where they are worn, and test under pressure before we leave. That is how a shower repair stays fixed instead of turning into a callback.

What you receive with shower repair

Clear records from your shower repair job that you can keep and share.

Repair summary

What failed and what was replaced

Photo record

Images of the valve and drain before and after

Parts list

Cartridge, seats, and any other parts used

Test notes

Pressure and temperature results after repair

Cartridge wear versus valve body failure

Most shower drips are cartridge wear, but a cracked valve body needs a different repair, and the two look similar from the handle.

Cartridge wear

The most common cause of a dripping handle.

  • Drip from the handle
  • Fixed with a new cartridge
  • Seats replaced at the same time

Valve body failure

A cracked body leaks behind the trim.

  • Water behind the wall
  • Requires valve replacement
  • Wall opening needed

Drain or pan leak

Water shows below the shower, not at the handle.

  • Ceiling stain below
  • Flange or pan repair
  • Pan tested before closing

What we work with

  • Cartridges
  • Valve seats
  • Showerheads
  • Copper pipe
  • PEX tubing
  • Shutoff valves
  • Supply lines
  • Wax ring

Service ZIP codes

A list like this tells people straight away whether we cover their street for shower repair. Not listed? Call and ask — it only takes a minute.

  • 75455
  • 75456

Areas we serve in Mount Pleasant, TX

Based in Mount Pleasant and covering the places around it. Pick one for local details.

View all service areas

What customers say about our shower repair

Excellence service and diagnosis with courtesy and understanding of the whole issue. Went well beyond the norm to assist whereby I was able to resolve the problem. Especially considering it was a Saturday morning service call Thank you so much for your expert advice. Hot water again, yeah!!!

SamE Embras Jr
5 stars · 2 years ago · Google review

The service I received from NTP Plumbing in April was Absolutely EXCEPTIONAL! The technician/plumber name was Jeremy. He took care of my pipe issues efficiently and treated me like I was family. Jeremy had excellent customer service/interpersonal skills and he made sure the work done was in the spirit of excellence. I would be remiss if I didn't mention the wonderful service I received from the owner, James. He was so welcoming and genuinely kind. James was able to get me scheduled in so that my plumbing would be taken care of in a timely manner. Thank you NTP Plumbing for all you do and especially for the things I don't see.

Ozie Hollingsworth
5 stars · 2 years ago · Google review

I recently used NTP for a clogged kitchen drain. The job took longer than anticipated but James honored his quote and the work is guaranteed for 30 days. I would highly recommend NTP for any plumbing needs you may have.

No Name
5 stars · 2 years ago · Google review

This review is about a used-appliance sale, a separate line of business — not plumbing work.

They sell used appliances as well, fyi they r super nice ND very great prices! They delivered my fridge same day we're quick and nice. Thank y'all so much for being so efficient!!

Brittney Moss
5 stars · 2 years ago · Google review

They were very professional and courtious. Fixed all my plumbing problems

Tim Griffin
5 stars · 4 years ago · Google review

4.8 out of 5 from 16 Google reviews — 15 five-star and 1 one-star. Read all reviews for NTP Plumbing on Google.

All reviews
4.8 out of 5 · 16 Google reviews

Frequently asked questions about shower repair

Usually the valve cartridge no longer seals. Water keeps passing the cartridge and out of the head. We fit the matching cartridge and test the shutoff before we leave.

A worn mixing cartridge cannot hold the hot-and-cold balance, so the temperature swings when another tap runs. A new cartridge restores the balance.

It can be a scaled head, but in older Mount Pleasant, TX homes it is often a galvanised supply line narrowing with corrosion. We check the pressure at the shower and at the meter to find which it is.

Often, yes. Most cartridges come out through the trim plate on the shower side. If the valve body itself has failed, the wall has to be opened — and we will tell you before we start.

Need shower repair in Mount Pleasant, TX?

Call (903) 350-9085 and tell us what the shower is doing. We will fix the valve and check the pressure while we are there. Open 24 hours, Monday–Sunday.

Get in Touch with NTP Plumbing

Call (903) 350-9085 any time — NTP Plumbing is open 24 hours, Monday–Sunday. Tell us what you are seeing and we will talk you through shutting the water off if you need to. We serve Mount Pleasant, TX, including ZIP codes 75455 and 75456.

Thanks. Your request is in and the team will follow up shortly.