Faucet installation in Mount Pleasant, TX, fitted and tested

Faucet installation is the professional fitting of a new kitchen or bathroom faucet in a Mount Pleasant, TX home, with supply lines and shutoffs checked. A new faucet should feel solid, shut off cleanly, and not leak at the base a month later. NTP Plumbing installs kitchen and bathroom faucets across Mount Pleasant, TX, with new supply lines and shutoffs checked as part of the job. Open 24 hours, Monday through Sunday.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchenNew faucetLines checkedTested at pressure
  • We test firstWater off, lines drained
  • We protectTowel and bucket under sink
  • We check valvesShutoffs tested before install
  • We clean upOld fixture hauled away

What Our Faucet Installation Service Covers

Every install includes the basics that make a faucet last: removal of the old fixture, new supply lines, fresh seals, and a full leak test. If we find worn shutoff valves or a damaged drain assembly, we quote the added work before we do it.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
  • Old Faucet Removal

    We shut off the water, drain the lines, and remove the old faucet, supply lines, and drain assembly. We protect the sink and cabinet floor and haul the old fixture away with us.

  • New Supply Lines

    We install new braided stainless supply lines sized to the fixture. Old lines are a common leak point, so replacing them during the install is cheap insurance against a cabinet full of water.

  • Shutoff Valve Check

    We test the angle stops under the sink. If they will not close or are corroded, we replace them with new quarter-turn valves so you can shut the water off in an emergency.

  • Drain and Sprayer Hookup

    We connect the drain assembly and sprayer hose, check the gaskets, and test for leaks. On kitchen faucets, we confirm the sprayer retracts and the diverter works.

  • Full Leak Test

    We run hot and cold water, check every connection, and use a pressure gauge to confirm house pressure is in range. We do not leave until the sink is dry under the cabinet.

Homes and rentals

A kitchen faucet and a bathroom faucet install differently — hole spacing, spout reach, and supply layout all change with the sink — but the checks at the end are the same in a home and a rental. What changes is the access, the schedule, and who needs the paperwork for a faucet installation job.

For Homes and Rentals

We install kitchen and bathroom faucets in houses, condos, and rentals. We check the shutoff valves and supply lines so the new fixture runs leak-free.

  • Worn kitchen faucet
  • Corroded bathroom handles
  • Loose faucet base

For rentals and property managers

We handle faucet replacement in rental units. We schedule around tenant access and document the work for the property file.

  • Tenant turnover faucets
  • Bathroom fixture upgrades
  • Kitchen sink faucets

What faucet installation in Mount Pleasant, TX actually involves

A plain-language look at what Faucet Installation involves and when it is needed. The City of Mount Pleasant charges a $75 residential plumbing permit fee where a permit is required (inside city limits) — that is a City fee, not our price.

See how it works

Installing a faucet is more than swapping the fixture on the sink. The old faucet comes out, the deck is cleaned and checked for damage, the new faucet is set with the right gasket and sealant, and the supply lines and shutoffs are checked — or replaced if they will not close. Then the water goes back on and every joint is watched for a weep.

The jobs we see most are kitchen upgrades in Southgate and Downtown remodels, and bathroom refreshes in Northwood and Stone Briar. In older Mount Pleasant, TX homes the shutoffs under the sink are often original and seized; replacing them at install time is cheaper than an emergency call later. We fit the faucet you supply or one you ask us to bring, and we never push a particular make.

A faucet is only as good as the shutoff and supply line behind it.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
What it is
Removing an old faucet and fitting a new one, with the supply lines and shutoffs checked.
When you need it
A cracked body, a finish that has gone, or a remodel that calls for a new fixture.
What to expect
A solid mount, no leaks at the base, and shutoffs that close when you need them to.

How Our Faucet Installation Process Works

We keep the job simple and predictable. Here is what happens from the first call to the final test, whether it is a single bathroom faucet or a full kitchen upgrade.

  1. Call and Scope

    You call (903) 350-9085 and tell us what you have: the fixture, the sink type, and whether the old faucet is leaking. We ask about shutoff valves and supply lines because those often need replacing too. Most calls take a few minutes, and we give you a quote before we schedule.

    • Call
    • Scope
    • Schedule
    Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
  2. Shutoff and Removal

    On arrival we shut off the water at the angle stops or the main, then drain the lines. We lay a towel and a bucket under the sink and pull the old faucet, supply lines, and drain assembly. If a shutoff valve will not close, we replace it while we are in there.

    • Shutoff
    • Drain
    • Remove
    Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
  3. Deck Prep and Dry Fit

    We clean the mounting surface, check the hole spacing, and dry-fit the new faucet. On a bathroom install, that means checking the 4-inch or 8-inch centers and making sure the new spout clears the sink bowl. We set the gasket and align the handle positions before anything gets tightened.

    • Clean
    • Dry fit
    • Align
    Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
  4. Connect and Seal

    We connect the supply lines with new braided hoses, apply Teflon tape to the threads, and tighten the mounting nuts evenly. The drain and sprayer get connected and tested. We use a pressure gauge to confirm the house pressure is in range, because high pressure is a common cause of premature faucet failure.

    • Connect
    • Seal
    • Pressure check
    Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
  5. Test and Cleanup

    We run hot and cold, check for drips at every connection, and test the sprayer and drain. Then we wipe down the sink, haul off the old fixture, and walk you through what we did.

    • Test
    • Cleanup
    • Walk-through
    Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen

Tools and Methods We Use on Faucet Jobs

Move across a circle, or focus it and press Enter, for an illustrative thermal view of this faucet installation photograph.

  • Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen

    Basin wrench

    Reaches the mounting nuts behind the sink bowl where a regular wrench will not fit. It is the difference between a clean removal and a stripped nut.

  • NTP Plumbing technician with tools at a Mount Pleasant, TX home

    Pipe wrench

    Used on shutoff valves and supply fittings when they are stuck. We use it carefully so we do not twist the pipe behind the wall.

  • Plumber using leak detection equipment in a Mount Pleasant, TX home

    Teflon tape and pipe dope

    Seals threaded connections on supply lines and shutoff valves. The right amount prevents leaks without cracking plastic fittings.

  • Plumber replacing old pipe with new PEX in a Mount Pleasant, TX home

    Pressure gauge

    Checks house pressure at the hose bibb. High pressure is a common cause of faucet and supply line failure.

  • Plumber cleaning a clogged drain in a Mount Pleasant, TX home

    PEX crimping tool

    Used when we replace a section of supply pipe with PEX tubing. It makes a code-correct crimp that will not leak behind the wall.

Thermal views are illustrative, generated from photographs of faucet installation work in Mount Pleasant, TX.

Methods

  • Soldering torch

    For copper pipe repairs when a supply line needs to be cut and re-sweated. We use it with a heat shield to protect the cabinet and framing.

  • International Plumbing Code compliance

    We follow the IPC for supply connections, backflow protection, and drain assembly. That means the install passes inspection and works the way the manufacturer intended.

  • Manufacturer torque specs

    Faucet makers publish torque values for mounting nuts and supply connections. We follow them so we do not crack porcelain sinks or strip brass threads.

  • Pressure testing

    After the install we run the faucet and check every connection with a dry paper towel. Any moisture means we tighten or reseal before we call the job done.

  • Supply line replacement

    We replace old supply lines as part of the install unless they are clearly new. Braided stainless lines cost little and prevent the most common under-sink leak.

When to Schedule a Faucet Install

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen

Kitchen upgrade

A kitchen remodel needs a new faucet on a fresh sink.

We set the faucet with the right gasket, fitted new braided supply lines and stops, and tested every joint at full pressure.

Outcome: A solid mount, no weeps, and shutoffs that close.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen

Bathroom refresh

A vanity replacement needs new faucets to match.

We fitted both basin faucets, replaced the tired stops underneath, and checked the trap while the cabinet was open.

Outcome: A finished vanity with dry connections and working shutoffs.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen

Seized stop

The old faucet came off, but the shutoff underneath would not turn.

We replaced the seized stop before fitting the new faucet, so the next repair will not need the main shut off.

Outcome: A new faucet on a supply that can actually be isolated.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen

Rental kitchen

A rental kitchen needs a new faucet between tenancies.

We coordinated with the property manager, fitted the faucet and new supply lines, and left the old one for disposal.

Outcome: A fresh kitchen tap ready for the next tenant.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
DowntownSouthgateNorthwood

How faucet installation runs in Mount Pleasant, TX

Kitchen faucet installs are the most common, and they cluster where kitchens are being refreshed: Downtown remodels, Southgate ranches getting a new sink, and new-build finishes in Northwood and Stone Briar. Bathroom faucets follow the same pattern, usually as part of a vanity replacement.

In older homes the deck or the shutoffs can surprise you — a corroded stop or a pitted sink deck turns a simple swap into a repair as well, and we will tell you before we start. If your current faucet is only dripping, a repair may be all it needs; our guide on how to fix a dripping faucet in your Mount Pleasant, TX home helps you tell the difference.

  • Downtown Mount Pleasant, TX: Remodels in early-to-mid-20th-century homes. Old shutoffs and pitted decks are common, and we flag them before the new faucet goes in.
  • Southgate: 1970s brick ranches where kitchens are being refreshed. A new faucet usually goes in with new supply lines and stops.
  • Northwood and Stone Briar: Newer north-side subdivisions, where faucet installation work is usually on newer systems. Installs here are usually finish choices on a new build or a bathroom refresh.
  • Lake Bob Sandlin area: Lakefront homes where a faucet install often happens between stays. We test everything before we leave, since the house may sit empty.
  • Rentals and turnovers: A new faucet between tenancies lifts a kitchen for little money. We fit it and check the trap and lines at the same visit.
  • Supply lines and shutoffs: We check both on every install. A valve that will not close turns the next repair into a flood, so we replace it while the water is already off.
See where we work
  • We walk the sink and explain the plan
  • We lay protection and set up tools
  • We test the fixture and review next steps

From problem to finished result

Example — a typical call. The stories below are illustrative examples of the kind of faucet installation calls we take, not a record of a specific past job.

Plumber replacing a dripping faucet in a Mount Pleasant, TX kitchen
IllustrativeThe thermal view for this faucet installation job is generated from the photograph. It is not a measurement. Drag the handle to compare the before and after on this faucet installation job, or use the arrow keys once it is focused.
  • Dripping Kitchen Faucet Replaced

    Before: A kitchen faucet dripped constantly and the base was loose. The shutoff valves were original and would not close all the way, so the homeowner had to shut off the main to stop the water.

    After: We replaced both angle stops with quarter-turn valves, installed new braided supply lines, and set a new pull-down faucet. The drip stopped, the base is solid, and the homeowner can shut off the water under the sink.

    Wipe the faucet dry after use and check the aerator every six months. In hard water, soak the aerator in vinegar to clear scale.

  • Bathroom Faucet Upgrade

    Before: A bathroom faucet had corroded handles and a cracked supply line that left a small puddle in the vanity cabinet. The pop-up drain would not seal, so the sink drained slowly.

    After: We installed a new widespread faucet, replaced both supply lines, and installed a new drain assembly. The handles turn smoothly, the sink drains fast, and the cabinet stays dry.

    Check under the sink once a month for moisture. Replace the supply lines every five to seven years even if they look fine.

  • Rental Unit Faucet Replacement

    Before: A rental unit had a builder-grade faucet with a broken sprayer and a shutoff valve that was stuck open.

    After: We replaced the faucet, the shutoff valve, and the supply lines while we were there. The unit was ready for the new tenant.

    Tell tenants where the shutoff valves are and check the faucet at each turnover. A quick look saves a big repair later.

Faucet Problems We Fix With a New Install

Sometimes a faucet just needs a cartridge. Other times the fixture is worn out and a replacement is the smarter spend. Here is what we see most often in Mount Pleasant.

  • Constant dripFaucet drips constantly and runs up the water billA steady drip can waste a lot of water over a month and stain the sink bowl. Left alone, it can also rot the cabinet floor under the fixture. We pull the old faucet, inspect the shutoff valves and supply lines, and install a new fixture with fresh seals. If the cartridge is the only issue, we tell you that instead of selling a replacement.
  • Loose baseBase of the faucet is loose and water seeps under itA loose faucet lets water past the gasket and into the countertop or cabinet. Over time that means swollen particleboard and mold. We remove the faucet, clean the mounting surface, and reinstall with a new gasket and proper torque. If the deck is damaged, we repair it before the new faucet goes on.
  • Low pressureLow water pressure at the kitchen or bathroom tapScale and sediment clog the aerator and cartridge, and old galvanized pipe restricts flow. It makes everyday tasks slow and frustrating. We check the aerator, the supply lines, and the shutoff valves. If the pipe is the problem, we repair or replace the section with PEX or copper so the new faucet gets full flow.
  • Stuck shutoffOld shutoff valve will not close all the wayIf a supply line bursts, you cannot stop the water. That turns a small repair into a flooded kitchen. We replace the angle stops with new quarter-turn valves during the install. It gives you a working shutoff you can trust.

Why a Proper Faucet Install Pays Off

A faucet that runs clean, seals tight, and shuts off when you need it to.

  • No More Under-Sink Leaks

    A leaky faucet connection can rot a cabinet floor in a season. We pressure-test every supply line and drain fitting before we pack up, so you are not mopping up water a week later. That test catches the small stuff early.

  • Correct Water Pressure

    Clogged aerators and undersized supply lines cut flow to a trickle. We match the supply line size to the fixture and flush the lines before final hookup, so your new faucet runs at the pressure the manufacturer intended.

  • Code-Correct Connections

    Texas follows the International Plumbing Code in most jurisdictions, and that means proper backflow protection and no cross-connections. We install faucets with the right air gap and vacuum breaker where required, which matters most on outdoor hose bibbs and pull-out sprayers.

  • Longer Fixture Life

    Overtightened mounting nuts crack porcelain sinks and strip brass threads. We torque to spec and use the right washers and gaskets, which is why a properly installed faucet runs for years before the cartridge needs attention.

What you receive with faucet installation

Clear records from your faucet installation job that you can keep and share.

Job summary

What was installed and tested

Parts list

Supplies and valves replaced

Test notes

Pressure and leak check results

Care sheet

Simple maintenance steps

Single-handle vs. two-handle vs. pull-down faucets

The faucet style you choose changes the install time, the parts needed, and how the fixture holds up over time.

Single-handle

One lever controls hot and cold

  • Faster install
  • Fewer supply lines
  • Common in bathrooms

Two-handle

Separate hot and cold handles

  • More parts
  • Widespread spacing
  • Classic look

Pull-down

Sprayer built into the spout

  • Longer install
  • Diverter check
  • Kitchen favorite

What we work with

  • Faucets
  • Supply lines
  • Shutoff valves
  • Gaskets
  • PEX tubing
  • Copper pipe
  • Teflon tape

Service ZIP codes

A list like this tells people straight away whether we cover their street for faucet installation. Not listed? Call and ask — it only takes a minute.

  • 75455
  • 75456

Areas we serve in Mount Pleasant, TX

Based in Mount Pleasant and covering the places around it. Pick one for local details.

View all service areas

What Neighbors Say About Our Faucet Work

Excellence service and diagnosis with courtesy and understanding of the whole issue. Went well beyond the norm to assist whereby I was able to resolve the problem. Especially considering it was a Saturday morning service call Thank you so much for your expert advice. Hot water again, yeah!!!

SamE Embras Jr
5 stars · 2 years ago · Google review

The service I received from NTP Plumbing in April was Absolutely EXCEPTIONAL! The technician/plumber name was Jeremy. He took care of my pipe issues efficiently and treated me like I was family. Jeremy had excellent customer service/interpersonal skills and he made sure the work done was in the spirit of excellence. I would be remiss if I didn't mention the wonderful service I received from the owner, James. He was so welcoming and genuinely kind. James was able to get me scheduled in so that my plumbing would be taken care of in a timely manner. Thank you NTP Plumbing for all you do and especially for the things I don't see.

Ozie Hollingsworth
5 stars · 2 years ago · Google review

I recently used NTP for a clogged kitchen drain. The job took longer than anticipated but James honored his quote and the work is guaranteed for 30 days. I would highly recommend NTP for any plumbing needs you may have.

No Name
5 stars · 2 years ago · Google review

This review is about a used-appliance sale, a separate line of business — not plumbing work.

They sell used appliances as well, fyi they r super nice ND very great prices! They delivered my fridge same day we're quick and nice. Thank y'all so much for being so efficient!!

Brittney Moss
5 stars · 2 years ago · Google review

They were very professional and courtious. Fixed all my plumbing problems

Tim Griffin
5 stars · 4 years ago · Google review

4.8 out of 5 from 16 Google reviews — 15 five-star and 1 one-star. Read all reviews for NTP Plumbing on Google.

All reviews
4.8 out of 5 · 16 Google reviews

Faucet Installation Questions We Hear Every Week

Yes. We fit the faucet you supply, and we will tell you before we start if anything about it — the deck holes, the supply connections — needs an adapter or a change.

We check them on every install. If the lines are old, stiff or weeping, or the shutoffs will not close, we recommend replacing them while the water is already off.

Most installs are finished while we are there. Older homes can take longer if the shutoffs are seized or the deck needs work — we will tell you what we find before we start.

We test every joint at full pressure before we leave, and we watch the base and the connections while the water runs. If anything weeps during a faucet installation job, it gets fixed on the spot.

Get faucet installation in Mount Pleasant, TX scheduled

Call (903) 350-9085 and tell us which faucet you want fitted. We will check the deck, the lines and the shutoffs, and test everything before we leave. Open 24 hours, Monday–Sunday.

Get in Touch with NTP Plumbing

Call (903) 350-9085 any time — NTP Plumbing is open 24 hours, Monday–Sunday. Tell us what you are seeing and we will talk you through shutting the water off if you need to. We serve Mount Pleasant, TX, including ZIP codes 75455 and 75456.

Thanks. Your request is in and the team will follow up shortly.