How to fix a dripping faucet in your Mount Pleasant, TX home
A dripping faucet wastes water and money, and it usually means one small part inside has worn out. Here is how to diagnose and fix it in Mount Pleasant, TX — and when to call a plumber instead.
Summary: A faucet that drips once every few seconds wastes a surprising amount of water over a month, and the drip always gets worse. The cause is almost always a single worn part, and on most modern faucets that part is designed to be replaced. Start by checking that the shut-off valves under the sink turn.

A faucet that drips once every few seconds can waste a surprising amount of water over a month, and the drip always gets worse — never better. The good news is that the cause is almost always a single worn part, and on most modern faucets that part is designed to be replaced.
Before you start, find the shut-off valves under the sink and make sure they turn. If they are stuck or they drip when you move them, stop there — a failed shut-off valve is a job for us, because the next step is shutting off water to the house.
Fix a dripping faucet: find out what kind of faucet you have
The fix depends on the faucet type, and there are four:
- Cartridge faucets — the most common modern type, one lever or two knobs, with a cartridge that controls flow and temperature. A drip usually means the cartridge seals have worn.
- Ball faucets — a single lever over a ball with springs and rubber seats. Drips usually mean worn seats and springs.
- Compression faucets — two separate hot and cold handles that you tighten to close. A drip means the rubber washer on the stem has worn or the valve seat is pitted. Common in older Mount Pleasant, TX homes.
- Ceramic disc faucets — a single lever with two ceramic discs. Very durable, but a cracked disc or worn seal will drip.
If you do not know the type, take a photo of the faucet and, once it is apart, of the part. A plumbing supply counter can match a cartridge from a photo and a measurement.
Fix a dripping cartridge faucet
Turn off the water at the shut-off valves, open the faucet to release pressure, and plug the drain so small parts cannot fall in. Remove the handle — usually a small screw under a cap or behind the lever — then remove the retaining nut and lift the cartridge out. Note its orientation before you remove it; it only fits one way.
Take the old cartridge to the supply counter and match it exactly. Fit the new cartridge in the same orientation, reassemble, and turn the water back on slowly. Check for leaks around the handle and the base before calling it done. If the drip continues with a new cartridge, the valve seat inside the faucet body is damaged and the faucet itself needs replacing.
Fix a dripping compression faucet
Compression faucets drip because the washer at the end of the stem no longer seals against the valve seat. Shut off the water, remove the handle and the packing nut, and unscrew the stem. The washer is held on the end of the stem with a small screw — replace it with one of the same size and thickness.
While the stem is out, run a finger over the valve seat inside the faucet body. If it feels rough or pitted, the new washer will not seal for long. A seat wrench can smooth a mildly damaged brass seat, but a badly pitted seat means the faucet has reached the end of its life. Compression faucets are common in the 1970s-era homes around Southgate and downtown Mount Pleasant, TX, and at that age a full faucet replacement is often the better spend than a third washer.
When a drip means replace, not repair
Replace the faucet when the body is corroded, the finish is flaking into the water, the valve seat is badly pitted, parts are no longer available, or the faucet has been repaired twice and still drips. A new faucet also brings modern water-saving flow rates and a fresh supply connection — the braided supply lines and shut-off valves under an old sink are often as worn as the faucet itself.
Note the permit position: under Texas law, replacing a lavatory or kitchen faucet does not need a City permit. The work must still comply with the plumbing code, and any new supply connections must be sound. Our faucet installation service in Mount Pleasant, TX covers the swap, including new shut-off valves and supply lines where the old ones are past their life.
Drips that are not the faucet
Water under a sink is not always a faucet drip. Check the supply line connections, the trap joints, and the base of the faucet where it meets the sink — a leak at the base usually means the mounting gasket has failed, not the cartridge. A drip from the spout only when the water is running, with water also appearing under the sink, points to the supply lines or the shut-off valves.
If the drip is from a shower or a tub faucet instead, the same cartridge logic applies — but the access is different, and a shower valve sits behind tile. Our faucet repair service in Mount Pleasant, TX and shower repair service in Mount Pleasant, TX cover both, and a leak detection visit in Mount Pleasant, TX is the right call when you can hear water running but cannot see where it is coming from.
Get help with plumbing in Mount Pleasant, TX
A dripping faucet is a small part and a short job — until the shut-off valve will not turn or the seat is pitted. If you hit either one, stop and call us. Call NTP Plumbing at (903) 350-9085 — open 24 hours, Monday–Sunday.